40’/45’/48’/53’ Slider Tridem

Overall Length: 40’-8” or 45’-8” or 48’-8” or 53’-8” (Excluding dock bumpers) Overall Width: 96” (over tire 102”)

Overall Height: 58”

Fifth Wheel Height: 47 ± 1”

Rear Bolster Height: 48 ± 1”

Kingpin Location: 24” (From the rear face of the front bolster)

Landing Gear Location: 113-3/4” (From the kingpin center)

Tridem location: 41-3/4” (From rear face of rear bolster to rear axle center when extended)

Axle Spread: 60”+60”

Slider Bogie Setting: 48” travel in 4” increment

Tare Weight: 11,100 lbs ± 2%

Payload: 67,200 lbs (30,480 kg)

Specifications
Warranty Policy

Main beam	POSCO (Vietnam) W12@19lb/ft hot-rolled H-beam, ASTM A572 Grade 50 or equivalent.
Cross member	3/16” thick × 2 1/2” wide × 4 3/4” deep channel with profiled bar type diagonal brace for extension frame and 3/16” thick × 3 1/8” wide × 6 5/8” deep channel with profiled bar type diagonal brace for the rear main beam.
Upper Coupler	5/16” pick up plate with JOST 2” diameter square type king pin per SAE standard, 380-420 HB, with 2” water drain holes, design to be integrated with main frame through welding.
Front Bolster	8″ wide x 10″ high x 3/16″ thick open section, with 3-1/2″ chamfer in full length for gathering container in operation. 7-way receptacle and glad hands are in the center of front bolster. Casted corner caps (TOCA 905-940-000-RS/CS).
Front Locking pin	TOCA 905-910-000-LH/RH
Rear twist Lock	TOCA 905-130-000-90-LH/RH
Rear Bumper	4” x 4” x 3/16” square tube step with taper “H” section vertical member. Bar is bolted to uprights. The bumper is bolted to rear bumper mounting bracket welded on main beam.
Slider Beam	A sidemount friction slider with “Z” type slider rail fabricated by hi-tensile minimum 80,000 psi steel, 3/16” thick crossmembers reinforced with gussets. The slider with four (4) index pins operated mechanical manner. Lock pin mechanism with removable and replaceable components.
Landing Gear	AXN FW32E00J with 60,000 lbs capacity, 2-speed 17” travel with low “T” shoes. Crank handle is located on the driver’s side of the chassis. Pre-painted BLACK RAL9005 color. Landing gear brackets are bolted on the main beam as the layout.
Suspension	AXN sidemount OS 60” tri-axle, overslung configuration with medium-arch 3-leaf spring (355-00). Pre-painted BLACK RAL9005 color.
Axles	AXN 5” round axles with 22,500lb capacity; 77.5” track, Q+ 16.5”X7” 4707Q brake with AXN R23 linings. Dust shields are provided. Pre-painted BLACK RAL9005 color. 1.5-28 spline, HALDEX 5.5” automatic slack adjusters with stroke indicators. Reserved PSI interface; Heat Sensing Labels. Axle Installation orientation: 90 degrees REAR, chambers DOWN (2 abs ready front and rear, 1 non abs mid per unit).
Wheel end	AXN Hub & Drum Assembly P/N H30-0647BFNTZ/H30-0647BFNZ,STEMCO 358-4009 Integrated Sentinel Hub Cap, STEMCO seals and bearings. Spindle nut: STEMCO Pro-Torq P/N 447-4743. (5-year warranty wheelend).
Wheels	SUNRISE (Vietnam) 22.5 x 8.25 10-stud hub-piloted wheels with 5 hand holes and with TR572 valve stem. Pre-painted white color.
Tires	SAILUN (Vietnam) 11R22.5-16PR tubeless type, S668 tread without owner’s logo.
Brake System	SEALCO 110800 spring brake priority valve system, SEALCO 110580 control line valve and WABCO 4S/2M ABS system. PHILLIPS glad hand 12-13807 and 12-13607, 3/8” blue air tube for control and 1/2” red for supply. HALDEX Goldseal T30/30, 2.5” stroke brake chamber. FUWA air tanks.
Electrical	GROTE mold seal wiring harness, Reserved PSI and GPS connector. GROTE LED lights (amp connections for S/T/T lights and .180 bullets for others). The theft proof design used for 4” LED lighting
Electrical Receptacle	GROTE die cast nose box with solid pins.
Document Holder	PHILLIPS 16-802. Installed on roadside near crank handle.
Conspicuity tape	“AVERY” brand. Installed per federal regulations.
Painting	Abrasive blast of all metal surfaces – not less than SA-2.5 to achieve clean bare steel. Surface will be coated with electrophoresis primer and powder topcoat. Color BLACK RAL9005 and at the corner painted YELLOW color. Total thickness not less than 80μm after dry membrane. Coating supplier: Local supplier (Vietnam).
Hubodometer	NONE.
Tire Inflation System	NONE.
Mud flaps	20”x24”x1/4” (508X610X6mm) BLACK PVC mud flaps with “customer” logo and address.

No.	Part Name	Manufacturers Name	Time	Warranty Information
1	Frame	Thaco Trailers	5 Years	THACO INDUSTRIES TRAILERS AND HEAVY STEEL STRUCTURES MANUFACTURING LIMITED LIABILITY COMPANY Add : Chu Lai IZ., Nui Thanh Town, Quang Nam province, Vietnam Office: (+84) 2353.565.327 Website: https://thacotrailers.com/
2	Paint(ED + Top coat)	PPG	Painting: 7 Years